AEG WS 13-125 XE

Advantages: Power,
smooth start,
anti-vibration handle,
speed regulator,
keyless nut,
keyless protective cover
long (4m) rubberized power cord.

Disadvantages: If you dig:
the power button, you can accidentally turn off the tool, if you work without a handle and hold the body with both hands (but these buttons on most small Bulgarians).
The diameter and weight are large, it is hard to work with one hand, but this is a result of a powerful engine. But for safety, it is only possible to operate two angle grinders

Comment: I bought for grinding log house. It was necessary to have a car with an obor regulator, because the wood should be polished at low revs.
For the price was acceptable, I took for 5000 with a tail. I polished about 250 m2 of logs - everything is alive, the brushes almost never faded. There are no backlashes in bearings yet. Do not buzz. Rubber cable - THING, most of the work fell on the minus temperature, the cable becomes denser, but bends, does not break in the cold,
I tried to cut a little, when cutting works, the keyless nut and keyless protective casing are very convenient.
I also liked the anti-vibration grip, I now wear it on the second grinder of a larger diameter.
It fulfills itself by 110%. Recommend!

Advantages: Everything that LBM has to do, all functions at height. The price is very good. Cord 4 meters. The quality is decent, German.

Disadvantages: After a year of work in the "housing man". Burned on-off button. Made with colleagues an additional button on the body plus blue electrical tape. I can only find fault with the weak to the touch of the fastening of the electric wire to the body. We'll see, but this is not critical.

Comment: Smooth start-up, support and adjustment of turns is super, especially after bad machines. On the old ear grinding wheel vibrated terribly. On this same disk works almost smoothly, does not shake. Very satisfied.

Advantages: A smooth start, a good nut, support for speed under load and their adjustment, a small gearbox.

Disadvantages: It seemed that the power almost corresponds to the declared one (see comment)

Comment: I bought a few months ago, before it was KRESS, 1400 watts, there is something to compare with))). In general, the car justifies itself, the low price (relatively) but justifies itself when buying exclusively for domestic purposes (for yourself, the garage, the cottage, etc.). There are nuances: during the load, the support of the constant turns does not work immediately (I compare all the characteristics with the KRESS there, it worked faster), the power button is not very pleasant, there is a suspicion that the hook will move closer (hold the button, feel the button, you will understand) casing, and in my opinion the cooling system is rather weak (it is heated, but not critical). I cut everything, in principle, in the concrete, metal itself, polished the wood (speed adjustment helps a lot), used the disk to grind the concrete, in my opinion it pulls quietly (if you don’t choke the instrument), it’s comfortable in the hand, the weight is quite normal .As for power, the difference is noticeable (KRESS), it seems to be only 100W, but the sensations when working are completely different, some brands with a power of 1200W produce a more serious output per circle. Conclusion: for personal use, for a couple of times a week for this price the machine is what you need, for such a price it is very difficult to find a similar solution. In general, I advise. By the way, when you first started, I paid attention to the smell)))))) It does not smell like a cheap oil (who knows, he will understand)
R.S. When I work, I always try to take care of the tool; I don’t reap the maximum out of it all the time, and I advise you. And most importantly, you need to work sober !!!!!!!!)))))))
I want to add, 2 years have passed. The machine is still in working condition, but there is a nuance .... Watch the brushes very carefully, if you miss a bit, there is a chance to kill the collector, there is no shot in the brushes. When sanding wood, it became dusty, decided to clean it cardinally, found practically complete wear (before wires) of brushes and, accordingly, slight wear of the armature collector. Brushes replaced by Makitovsky with a "shot." I do not remember the size, they fit perfectly, there is infa in Google)))

Advantages: Smooth start, ergonomic handle, fast fixation of the disc, adjustable shield, speed control, long cord, low price.

Disadvantages: It is heated at low revs, the clamp of the fixing nut broke off, it was enough to turn it with a slight jamming of the pliers. No stabilizer speed, immediately stops under load. Began to stick the power key, the machine continues to work in the off position. There was a knock on the gearbox when the power was turned off.

Comment: Their money is worth it, all of the above disadvantages apply to any angle grinders with similar characteristics, for everything is now of very mediocre quality. Considering that they ask for this little bit, this is the best of the worst. The machine works in difficult conditions, participating in the grinding and finishing of the log house. I tried to grind on it with nylon brushes at low revs (the log burns above). The motor heats up almost immediately, the stabilizer does not hold the speed at all, it is worth pressing a little, it stops immediately. Therefore, I use it on the sidelines, as an auxiliary with a different snap-in, and I try not to twist below average turns. For grinding it is better to use a polisher with a different gear ratio. By constructive - a vacuum cleaner, pulls all the dust into itself from below and throws it out through the holes in the gearbox cover. The bottom holes, in my opinion, are small and unsuccessful. I cool around 5 minutes after work at the highest speed, at the same time the dust accumulated in the internal cavities flies out. Not yet disassembled, but began to tap the gearbox after turning off. I am personally strained by the start button, it is not always fixed the first time and you can just as easily be hooked on and off during operation. The best solution is to drown it in the case. In addition, recently she began to stick when turned off, continuing to turn the grinder. There was never a problem with the wire, although it fell and hung on my cord more than once. Let's see how much it is enough, but if it breaks, I will take, most likely, the same.

Advantages: Great choice!

Disadvantages: For one and a half year of daily use I did not find a single minus!

Comment: A good unit for professionals! I liked the keyless nut very much, it saves a lot of time, even if the disk bites! The anti-vibration side handle is comfortable in the hand. The power cable, too, didn’t twist! and 3 years warranty! Buy will not regret!

Advantages: + Adjustment of turns
+ rev control (supports the established number of revolutions regardless of the load)
+ long cord
+ Very fast disc replacement and instant adjustment of the casing position without the use of tools.
+ fits well in hand

Disadvantages: - not found

Comment: Great choice!
I was always afraid to work with the grinders, especially after the case when the disc shattered and flew to the face. Then I was lucky and there were no injuries, but I have since avoided the grinders.
But it became necessary to cut the car body. After comparing all the models, I came to the conclusion that this model with its characteristics, considering its cost, will probably be the best! Did not lose! I put 2800 turns / min., Due to the function of support turns - it cuts like clockwork! In this mode, it works quietly, there is no vibration! It's not scary at all, if you twist the disk - it will just stop. At such a speed he will not cause injuries (of course glasses or a shield are necessary). Generally I do not understand why grinders 11,000 revolutions per minute?

Advantages: smooth start-up, speed adjustment, constant electronics, sewn up from biting the disc, the protective casing rotates almost 360 degrees (I am left-handed, this is convenient) powerful not to warm up competitors more expensive.

Disadvantages: button on unreliable absence from unintentional inclusion no case

Comment: This is the first Bulgarian, but I managed to grind and cut and clean it and cut the wood, I am satisfied