RusNIT 208M
detailed information
9.8 / 10
Rating
Characteristics of RusNIT 208M
- Type: electric
- Power: 8000 W
- Voltage: 220/380 V
- Tank capacity: 7 liters
- Rated current: 37 / 13.7 A
- Heating Area: 60-80 sq. M
- Indoor temperature: 5-30 ° C
- Operating pressure: 0.3 MPa
- Dimensions: 500x320x210 mm
- Net weight: 12 kg
- Smooth temperature selection
- Three power steps
- Automatic control
- Safety thermal switch
- Coolant control sensor
- Panel with indicators
- Coolant temperature limitation
- Spray protection
- Heating accuracy up to 0.5 ° C
Reviews about RusNIT 208M
Evaluation
4
Advantages: 1. Works without complaints. There were no failures.
2. The power is sufficient for heating a house of 65 square meters with an average level of thermal insulation in the cold of -30 degrees. And this is not the limit.
3. Temperature control sensors (air wire) and coolant temperature work accurately, the system allows fluctuations in air temperature not more than 2 degrees.
4. Pleasant appearance, everything is succinct. Compact.
5. It is possible to connect an external wireless thermostat.
6. There is a possibility of both single-phase and three-phase connection.
7. The pump control system has two modes: automatic (the pump is turned on when the heating elements are running and a little after they are turned off) and forced permanent. The second allows for one pump parallel to the heater to connect another - wood, coal.
2. The power is sufficient for heating a house of 65 square meters with an average level of thermal insulation in the cold of -30 degrees. And this is not the limit.
3. Temperature control sensors (air wire) and coolant temperature work accurately, the system allows fluctuations in air temperature not more than 2 degrees.
4. Pleasant appearance, everything is succinct. Compact.
5. It is possible to connect an external wireless thermostat.
6. There is a possibility of both single-phase and three-phase connection.
7. The pump control system has two modes: automatic (the pump is turned on when the heating elements are running and a little after they are turned off) and forced permanent. The second allows for one pump parallel to the heater to connect another - wood, coal.
Disadvantages: 1. A little magnetic starter buzzes, which supplies power to the entire device and to the pump. And the intensity of the buzz changes when you turn it off / on. You can achieve a fairly quiet job.
2. Electrical connection is not for the faint of heart. Phase, zero and earth connections are located at three different locations, require soldering to the ring terminators and are connected by tightening the nut. Tighten these nuts is extremely difficult, especially for zero because of its location. It is completely unclear why it was impossible to use the connection on the clamp as in circuit breakers, especially since the current allows? I remind you that the installation will require a soldering iron and solder.
3. The device is not fully automatic in the sense that the included heating elements and the corresponding power in the range of 3-5-8 kW are selected only manually. This is inconvenient, for example, in the case of a cold snap, when a 3 kW heater will simply not be enough - as a result, the heating system cannot automatically maintain the desired temperature.
2. Electrical connection is not for the faint of heart. Phase, zero and earth connections are located at three different locations, require soldering to the ring terminators and are connected by tightening the nut. Tighten these nuts is extremely difficult, especially for zero because of its location. It is completely unclear why it was impossible to use the connection on the clamp as in circuit breakers, especially since the current allows? I remind you that the installation will require a soldering iron and solder.
3. The device is not fully automatic in the sense that the included heating elements and the corresponding power in the range of 3-5-8 kW are selected only manually. This is inconvenient, for example, in the case of a cold snap, when a 3 kW heater will simply not be enough - as a result, the heating system cannot automatically maintain the desired temperature.
Comment: The impossibility of full automation and a slight buzz can spoil your impression of operation, and connecting to the power grid takes more time than expected.
However, the advantages outweigh the disadvantages. Very good model. Recommend.
However, the advantages outweigh the disadvantages. Very good model. Recommend.
Filippov Leonid
February 19, 2017
RusNIT 208M is selected in the rating:
Top 10 electric boilers
